Crap

[PUMP 'HER']

So I take off from here a few minutes late to meet up with the McD clan, but not bad. Talk to kev when I'm just coming into Victorville. He's maybe a half hour ahead of me we are gonna meet at a gas station in Barstow, says he'll wait, no prob. Get off the phone with him and I looked in the mirror and think I see a spark, I keep looking and I see another one, coming from the left trailer wheel! Pull over and the bearings are toasted! Wheel is about to fall off! Managed to limp the next mile or so off of the freeway. Pull the wheel off luckily the bearings hadn't welded themselves to the spindle. Just missed the guy at Autozone by half and hour, told him I'd give him $50 to stay, he split. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/confused.gif Anyway we got a room and replaced the bearings in the morning with NAPA parts (thats where Danielle works couldn't stand the fact I was calling Autozone to begin with) by then it was around noon, I said forget it lets just go home. Lost the bearing buddy cap thing last October on the way home replaced them, but it was missing again this time. When I put the seal in on the back side of the hub it just slipped right in. It should be a hammer in thing. Looks like the hub has a few small cracks in it and is either letting the greese out or water in or both. Of course this dealio messed up the spindle so now that needs replacing, along with the hub. Screw it I'd like to just replace the whole trailer, maybe a new Extreme?!?! http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif All in all it was an F ed up trip, the only thing that could have been worse is if it had happened way out in the middle of no where. So I guess what come around goes around, after all the smack I talked to McD about Smoke on the water last month, I got some coming my way. Bring it on McD!! The worst part is, I was the firewood guy, sorry guys hope you were able to find some somewhere. Glad I had it with me though as I needed it to block up the trailer while I had it jacked up.

[BADFISH II]

that SUCKS! http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/mad.gif

[Red Horse]

Sorry to hear that Brandon.

My trailer wheels are all greasey. I over lube them all the time. When I was younger, my Dad and I were stuck on the side of the road for a long time with a similar situation.

[dicudmore]

sorry to hear that....
any kind of break down sucks!

[Rude]

sorry to hear about your crappy weekend bro!! hopefully your next trip out will make up for it.

[B-Rad502]

Sorry about the trailer problems Brandon. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/sad.gif Your crew stopped by the sand bar yesterday to hang out for a few minutes and told me about your misfortunes. I guess the new Carlisle tire I blew out on the way to the lake Friday was not too big of a deal now!

[PUMP 'HER']

Yeah it was no fun spending the night in Victorville, (right Greg?), had to get a new tire also, I guess the heat must have blistered it or something. Cool part is they have changed tread patterns since my original purchace and after two non repairable flats and this dealio I now have all three tires the same again.

[Essex502]

That sux. I've had my share of trailer problems in the past. I'm now glad I don't tow often over 4 miles. And then I check the grease before every tow.

[NordicHeat]

Hey B-Rad,
with the Carlisles is not if but when will they blow.
Our trailer was two seasons old last year and we lost 4 of 6 Carlisles within 6 weeks. My buddy lost 3 of 4 on his Rage (same year). I think T&B and several others have had the same issues with these.
They did send me 7 new tires and a rim with no questions asked. Hmmmmm?
Guess I'll wait until the first one blows and then replace them all with Goodyears http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/insane.gif
Dave

[Essex502]

We've owned our Extreme trailer since 2000 and have not lost a Carlisle tire. Before we moved the trailer and boat to LHC we towed back and forth from Los Angeles to Havasu, Mead or Mohave with a trip to Bishop thrown in. What I don't do is roar down the highway at 80 like some folks do while they're towing (no offense to anyone here!http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wink.gif and I check tire pressure every time I tow. I generally look over the trailer at every stop and if necessary top off the tires with a portable compressor that is always in the truck. Knock on wood... the Carlisle's have been fine. Trailer has always been stored indoors and liberal amounts of ArmorAll used on the sidewalls just for grins.

[MOWtown]

Sorry bout your trip. My dad and I had a similar experience on the side of some Minnesota road a few years ago. The bearings DID melt to the spindle...not an easy fix on the side of some road. Luckily we were able to tie down the spindle to the frame and limp home on 3 wheels.

Little advice beside the obvious "grease your bearings". If you think that your brakes are sticking, even the slightest amount, don't chance it...pull the shoes. My dad said that the faint squeeking noise coming from his drum was "no big deal"...he'd fix it when we got home. My assss. We had a damn bon fire coming from that wheel in about 1/2 hour http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/biggrin.gif . Sticking brakes equal heat which cooked the grease then bearings...you know the rest.

[just another payment]

What air pressure do you all run your tires at?

[kevnmcd]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (PUMP 'HER' @ May 15 2004, 7:10 pm)</td></tr><tr><td id="QUOTE">So I guess what come around goes around, after all the smack I talked to McD about Smoke on the water last month, I got some coming my way. Â*Bring it on McD!! Â*[/QUOTE]<span id='postcolor'>

'nuf said! Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/tounge.gif

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote </td></tr><tr><td id="QUOTE">The worst part is, I was the firewood guy, sorry guys hope you were able to find some somewhere. Â*[/QUOTE]<span id='postcolor'>

Kids kept asking all weekend....can we have smores tonight? Â*And all I could say was "I am sorry kids, PH was in charge of that and he decided not to come out!" Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wow.gif

[digginfordollars]

I know some peeps who carry a whole spindle, bearings and hub mounted right to the spare tire. They are not very expensive and pretty easy to change on the side of the road. At least you don't lose your whole weekend. I carry extra bearings with me but have not loaded in a spare spindle yet. Maybe I'll pick one up this week. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/rolleyes.gif

[PUMP 'HER']

Spindle doen't look like an easy repair on mine. Don't see a way of doing it with out cuting out the old and welding in a new one. Maybe I'm wrong, I've been wrong before.

[Music to my Ears]

Yo Brandon, sorry to hear about your bearing misfortune. Even more sorry you couldn't make it out. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/sad.gif We definetly missed you guys.

I'm not even going to give you crap about not bringing the firewood. I figure Kevin will give you enough of that. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif

[kevnmcd]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (Music to my Ears @ May 18 2004, 10:21 am)</td></tr><tr><td id="QUOTE">I'm not even going to give you crap about not bringing the firewood. I figure Kevin will give you enough of that. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif[/QUOTE]<span id='postcolor'>
I haven't decided whether or not to stoop to his level, yet. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/rolleyes.gif I may decide to take the "high" road...this time. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif

[PUMP 'HER']

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (kevnmcd @ May 18 2004, 11:46 am)</td></tr><tr><td id="QUOTE">I may decide to take the "high" road...this time. Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif[/QUOTE]<span id='postcolor'>
You gotta be kidding me! Hey would it help if I told you Danielle said I didn't bring enough anyway?

[vegas ultra]

p.h. the same thing happend to me cumming back from mead 2 or 3 years ago . had to have the spindle cut off and a new one welded on . you might be better off getting a new axle my tire dosent wear right on that side .the weld shop i had it done at sucks . http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/mad.gif

[kevnmcd]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (PUMP 'HER' @ May 18 2004, 5:33 pm)</td></tr><tr><td id="QUOTE"></span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (kevnmcd @ May 18 2004, 11:46 am)</td></tr><tr><td id="QUOTE">I may decide to take the "high" road...this time. Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif[/QUOTE]<span id='postcolor'>
You gotta be kidding me![/QUOTE]<span id='postcolor'>
I think that taking the "high" road here might be more fun than the "low" one. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif

[PUMP 'HER']

Just for kicks I stoped by Extreme today. 4k for a new tandem trailer, with brakes. What do you all think, would it help to build value in the boat for a future sale or would it not really be worth it, just fix what I got or maybe a cheaper new trailer. Curent one is a single axle Vanson, with some damage to the rear where it nailed the ground, (previous owner) it could use a little TLC, sorta like McD gave his last year. Hey Kev you wanna make a few bucks? http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif

[red_n_vegas]

what size is your boat?

[digginfordollars]

I thought the spindles were bolted on but I looked at mine tonite and they are welded too. I guess it wouldn't be an easy fix unless you had the underhood welding system. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/ohboy.gif

I don't think you would get your money back by buying a new trailer. Most buyers barely look at the trailer unless it is a serious hunk of junk.

[Rude]

you will NOT get your money back when/if you go to sell later. if you are even somewhat considering selling/trading your current ride, i would fix what needs fixing without going overboard. if you are interested in keeping your boat for long time it may be worth the $$ for sweet trailer. i was very seriously considering a new trailer for the nordic right up until the time we bought the daytona.

[PUMP 'HER']

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (red_n_vegas @ May 20 2004, 8:15 pm)</td></tr><tr><td id="QUOTE">what size is your boat?[/QUOTE]<span id='postcolor'>
19' around 2000 pounds.

[PUMP 'HER']

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (digginfordollars @ May 20 2004, 9:03 pm)</td></tr><tr><td id="QUOTE">I don't think you would get your money back by buying a new trailer. Most buyers barely look at the trailer unless it is a serious hunk of junk.[/QUOTE]<span id='postcolor'>
I know I wouldn't get all of my money back, but if it would add say 2k to the value as opposed to spending a grand on refurbishing or buying a cheaper trailer @ 2k maybe it would be worth it. The current trailer is not quite a hunk of junk but could use some work, and is only a single axle without brakes. Right now the plan is a new ride in a year or two. As is the boat should be worth around 13k. I've seen them for sale for that amount anyway.

[kevnmcd]

PH - Sorry...I don't have time to restore anything right now. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/sad.gif I wouldn't recommend buying a new one either. A new trailer won't do anything for the sale price of your boat down the road. I would recommend just getting a new axel, that way you know it is straight and then take it to a shop and have it sandblasted and painted. Then you have a great looking trailer for a fraction of the cost. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/smile.gif

[PUMP 'HER']

Sounds like it may be the winter project. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wink.gif

[kevnmcd]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (PUMP 'HER' @ May 21 2004, 08:48 am)</td></tr><tr><td id="QUOTE">Sounds like it may be the winter project. Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wink.gif[/QUOTE]<span id='postcolor'>
That might work. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/rolleyes.gif

[PUMP 'HER']

How perfect does a spindle need to be? Its not bad I'll post some pics in a little bit. Anyone?

[digginfordollars]

If it is not bent and you can slide the bearing races on it without a lot of slop, it should be fine. If it has big burrs on it you may be able to take a file and sandpaper to it to clean it up. The bearings don't run on the spindle so it doesn't have to be perfect.

[PUMP 'HER']

Bottom

[PUMP 'HER']

Top

[PUMP 'HER']

Front

[PUMP 'HER']

Back notice the framing hammer marks, hey when you stuck your stuck and gotta use what you've got right, so my aim isn't all that great. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/biggrin.gif

[PUMP 'HER']

Oops forgot the pic

[kevnmcd]

That spindle looks pretty worn, IMHO. You might look at replacing that thing.....that might be your problem as to why you keep wasting bearings on that side. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wink.gif

[digginfordollars]

Yeah that thing looks hammered, I would replace. If you are coming up this weekend stop in Friday nite (with a replacement) and we will weld a new one on for ya.

P.S. Don't show up at two AM http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/crazy.gif

[PUMP 'HER']

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (digginfordollars @ May 25 2004, 10:23 pm)</td></tr><tr><td id="QUOTE">Yeah that thing looks hammered,[/QUOTE]<span id='postcolor'>
Yeah 'cause I used a hammer on it. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/rolleyes.gif Talking to a guy at Zieman today he says it very tough to replace a spindle because of the difficulty in setting the camber the same. Looks like around $300 to replace the whole axle, maybe this would be a better route? But damn I could buy something fun for $300. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/biggrin.gif

[kevnmcd]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (PUMP 'HER' @ May 25 2004, 11:17 pm)</td></tr><tr><td id="QUOTE"></span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (digginfordollars @ May 25 2004, 10:23 pm)</td></tr><tr><td id="QUOTE">Yeah that thing looks hammered,[/QUOTE]<span id='postcolor'>
Yeah 'cause I used a hammer on it. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/rolleyes.gif Â* Talking to a guy at Zieman today he says it very tough to replace a spindle because of the difficulty in setting the camber the same. Â*Looks like around $300 to replace the whole axle, maybe this would be a better route? Â*But damn I could buy something fun for $300. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/biggrin.gif[/QUOTE]<span id='postcolor'>
$300? Sounds like cheap insurance to me....especially if it will get you to the lake/river so you can play all weekend. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/rolleyes.gif Better than sitting on the side of the road at midnight on your way with bearings welded to your spindle. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wink.gif

[PUMP 'HER']

Yeah thats what I have decided needs to happen. Gotta go axle shoping today. Hope I can get it done today or tomorrow.

[kevnmcd]

As long as it is done before Father's Day weekend. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/biggrin.gif

[PUMP 'HER']

Right!

[Red Horse]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (digginfordollars @ May 25 2004, 11:23 pm)</td></tr><tr><td id="QUOTE">Yeah that thing looks hammered, I would replace. If you are coming up this weekend stop in Friday nite (with a replacement) and we will weld a new one on for ya.

P.S. Don't show up at two AM Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/crazy.gif[/QUOTE]<span id='postcolor'>
What kind of welder do you have.....buddy.

Need a favor. Have some trailer stuff to do as well. My shop is full of a holes right now so I cant use my stuff (actually works stuff)

[digginfordollars]

I've got Miller 250 wire feed and a Lincoln AC buzz box. Anytime you're ready I'll be here. Oops, not Thursday, kids have practice. Friday is good, should be home getting the boat ready most of the day.

[Red Horse]

Appreciate that. It wont be Friday. Gotta get the boat ready for Sat.

I need to weld my fender back on. I have a ghetto trailer and a half with only one fender.

[digginfordollars]

I'll be around tomorrow afternoon till 6 if you want to do it then. Be back from practice around 9:30. The wife is out of town so I can stay up as late as I want.

[PUMP 'HER']

Oh sure you tell RH you can stay up late but me, nooooo, "don't show up at 2 am". http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif

[kevnmcd]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (PUMP 'HER' @ May 27 2004, 07:21 am)</td></tr><tr><td id="QUOTE">Oh sure you tell RH you can stay up late but me, nooooo, "don't show up at 2 am". http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif[/QUOTE]<span id='postcolor'>
Get over it! He doesn't like you as much as he does RH! http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/tounge.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wink.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/smile.gif

[PUMP 'HER']

Shit I knew that, who would, I'm a pain in the ass, just ask Danielle.

[beer hunter]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (kevnmcd @ May 27 2004, 07:23 am)</td></tr><tr><td id="QUOTE"></span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (PUMP 'HER' @ May 27 2004, 07:21 am)</td></tr><tr><td id="QUOTE">Oh sure you tell RH you can stay up late but me, nooooo, "don't show up at 2 am". http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif[/QUOTE]<span id='postcolor'>
Get over it! He doesn't like you as much as he does RH! Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/tounge.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wink.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/smile.gif[/QUOTE]<span id='postcolor'>
LMAO http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif

[digginfordollars]

The wife will be back Fri afternoon so my priviledges will be revoked then. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/sad.gif Besides got to get up early Sat morn for the lake. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/biggrin.gif

[PUMP 'HER']

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (digginfordollars @ May 27 2004, 08:53 am)</td></tr><tr><td id="QUOTE">Besides got to get up early Sat morn for the lake. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/biggrin.gif[/QUOTE]<span id='postcolor'>
Same here!! Just got back with a new axle, looks like we are going to make it. No sense in fighting Friday trafic, we are going to get up around 3-4 Saturday morning and head out. See you all there.

Oh by the way, Pacific Trailer in Chino is awesome. After going to Kustom Trailer in Rancho, Arrow in Ontario, neither one had anything, the guy at Kustom tried to get me to take a used one that was too long, Arrow could order it and have it in a week. Pacific made me a new one while I went to lunch! $200, new hubs bearing seals, everything. They would have painted it if I wanted to wait a bit, told them forget about it I'll spray it myself, gonna do that total refurbish this winter anyway.

[dicudmore]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote </td></tr><tr><td id="QUOTE">No sense in fighting Friday trafic, we are going to get up around 3-4 Saturday morning and head out. See you all there.
[/QUOTE]<span id='postcolor'>

that was my plan exactly......

glad it worked out w/the trailer dealio

[kevnmcd]

Now maybe you won't be breaking down on the side of the road all the time. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif $200...not bad. Did you have to put the top down to get it in the Cobra? http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wow.gif

[beer hunter]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (kevnmcd @ May 27 2004, 3:17 pm)</td></tr><tr><td id="QUOTE">Now maybe you won't be breaking down on the side of the road all the time. Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif Â*[/QUOTE]<span id='postcolor'>
Something you've never done http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/ohboy.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif

[PUMP 'HER']

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (kevnmcd @ May 27 2004, 3:17 pm)</td></tr><tr><td id="QUOTE">Did you have to put the top down to get it in the Cobra? Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wow.gif[/QUOTE]<span id='postcolor'>
http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif
Momma let me use the Expedition for the day.

[PUMP 'HER']

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (beer hunter @ May 27 2004, 4:27 pm)</td></tr><tr><td id="QUOTE"></span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (kevnmcd @ May 27 2004, 3:17 pm)</td></tr><tr><td id="QUOTE">Now maybe you won't be breaking down on the side of the road all the time. Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif Â*[/QUOTE]<span id='postcolor'>
Something you've never done http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/ohboy.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif[/QUOTE]<span id='postcolor'>
Oh really, this sounds like a good story... http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/stare.gif

[beer hunter]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (PUMP 'HER' @ May 27 2004, 6:20 pm)</td></tr><tr><td id="QUOTE">Oh really, this sounds like a good story... http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/stare.gif[/QUOTE]<span id='postcolor'>
Let me refresh some memories http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wink.gif

[beer hunter]

I think those were Firestone 500's http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif

[PUMP 'HER']

Ah, thats not a break down, just a flat tire. besides he's smiling, you didn't see any fricking smilies on my face when I had my problems.

[kevnmcd]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (PUMP 'HER' @ May 27 2004, 6:20 pm)</td></tr><tr><td id="QUOTE"></span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (beer hunter @ May 27 2004, 4:27 pm)</td></tr><tr><td id="QUOTE">Now maybe you won't be breaking down on the side of the road all the time. Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif Â*<span id='postcolor'>
Something you've never done http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/ohboy.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif[/quote]
Oh really, this sounds like a good story... http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/stare.gif[/QUOTE]<span id='postcolor'>
Yep...lost TWO tires on the way out in March. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/insane.gif Ended up buying 4 new ones in Needles that weekend. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/sad.gif

[kevnmcd]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (PUMP 'HER' @ May 27 2004, 7:48 pm)</td></tr><tr><td id="QUOTE">Ah, thats not a break down, just a flat tire. Â*besides he's smiling, you didn't see any fricking smilies on my face when I had my problems.[/QUOTE]<span id='postcolor'>
Fortunately, I had BH with me....I only had one spare and had to use his too. http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/biggrin.gif Thanks again, BH.

[beer hunter]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (kevnmcd @ May 27 2004, 9:07 pm)</td></tr><tr><td id="QUOTE"></span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (PUMP 'HER' @ May 27 2004, 7:48 pm)</td></tr><tr><td id="QUOTE">Ah, thats not a break down, just a flat tire. Â*besides he's smiling, you didn't see any fricking smilies on my face when I had my problems.[/QUOTE]<span id='postcolor'>
Fortunately, I had BH with me....I only had one spare and had to use his too. Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/biggrin.gif Â* Thanks again, BH.[/QUOTE]<span id='postcolor'>
No problem Kevin! http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/smile.gif

[digginfordollars]

Pumpher, cool you'll make it, do you know your way to the marinas and around the lake? If not we can rendevous in the morning or otherwise we'll just see at LVHB.

[beer hunter]

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (digginfordollars @ May 27 2004, 10:44 pm)</td></tr><tr><td id="QUOTE">Pumpher, cool you'll make it, do you know your way to the marinas and around the lake? If not we can rendevous in the morning or otherwise we'll just see at LVHB.[/QUOTE]<span id='postcolor'>
Better do the escort thing D4$, if PH couldn't find his way to Park Moabi, he sure the hell isn't going to find LVHB Beach http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wow.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wow.gif http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif

[PUMP 'HER']

</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (digginfordollars @ May 27 2004, 10:44 pm)</td></tr><tr><td id="QUOTE">Pumpher, cool you'll make it, do you know your way to the marinas and around the lake? If not we can rendevous in the morning or otherwise we'll just see at LVHB.[/QUOTE]<span id='postcolor'>
Yeah I'm going to try to meet up with RH, and RNV around 8 am off of Craig and roll in with them.
</span><table border="0" align="center" width="95%" cellpadding="3" cellspacing="1"><tr><td>Quote (beer hunter @ May 28 2004, 04:16 am)</td></tr><tr><td id="QUOTE">Better do the escort thing D4$, if PH couldn't find his way to Park Moabi, he sure the hell isn't going to find LVHB Beach http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wow.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/wow.gif Â*http://www.lasvegashotboats.com/iB_html/non-cgi/emoticons/laugh.gif
[/QUOTE]<span id='postcolor'>
I could have found it, if I could have made it.:p